TELECOMMUNICATIONS AMPLIFIER
MSD-1488603 is a wide band amplifier covering the CDMA,
PCS, ISM & GSM bands. Specs are as followed:
Frequency: 20 - 1000 MHz
Gain: 31.0 dB min. 33 dB Typ.
Gain Flatness: +/- .75 dB max
Noise Figure: 10dB max.
Output Power: 29 dBm min 30 dBm Typ.
IP3: 38.0 dBm Typ.
VSWR I/O: 2.0:1/2.0:1
Outline:
OL-004169
Connectors: SMA-F/SMA-F
Operating Temperature: -29°C to +71°C
|
|
6.3WATT AMPLIFIER
MSI Model MSH-4716803-TC deliver 38dBm
(6.3W) of Power, an IP3 of 49dBm & 2nd Harmonics below -40dBc
Typ. These amplifiers are an excellent choice for point and
point
to multipoint systems at 3.4 to 3.6 GHz. They include a temperature
compensation
circuit which has a +/-1.5 gain window. Typical gain is 49.0 dB with a
flatness
of +/-1.0 dB. The I/O VSWR is 1.5:1 and the maximum current
is
3.8A @+12.0V. The amplifier has been designed to meet high thermal
stress
conditions and all units include
an internal voltage regulator and reverse-polarity protection.
LOW
PHASE NOISE
AMPLIFIER
1WATT Amp, Model MSH-6653601-LP
has been designed for Low Phase Noise using the latest hybrid
technology. The amplifier operates in the 8.0 to 12.0 GHz frequency
range. The typical pžš22 noise measurements at 10GHz have been
>-120dBc @ 100Hz and >-144 dBc @ 10kHz with a small signal gain
of 38 dB, P1dB of 30dBm, IP3 of +39dBm and better than 4.0 dB noise
figure. The input and output (I/O) VSWR is 2.0:1
with a maximum current of 1.2A @ +12VDC. The operating temperatures are
-40°C
to +60°C, with extended ranges available. Standard RF I/O
connectors
are SMA-F. The unit includes an internal reverse polarity protection
circuit.
Model MSH-6523602-LP has
been designed for Low Phase Noise using the latest hybrid technology.
The amplifier operates in the 6.0 to 10.0 GHz frequency range. The
typical phase noise measurements at 10GHz have been >-120dBc @ 100Hz
and >-144 dBc @ 10kHz with a small
signal gain of 32dB, P1dB of 27dBm, IP3 of +37dBm and better than 4.0
dB
noise figure. The input and output (I/O) VSWR is 2.0:1 with a maximum
current of 400mA @ +12VDC. The operating temperatures are -40°C to
+60°C
with extended ranges available. Standard RF I/O connectors are SMA-F.
The
unit includes an internal reverse polarity protection circuit. (9/4/97)
2GHz,
50 WATT AMPLIFIER
Microwave Solutions, inc.®' introduces
its new High Power amplifier (HPA) MSH-3709903-ISO design to be unconditionally stable for the use of
Uplink and Base Stations as well as for GPS and PCS. Manufactured with
soft board technology and using
discrete hermetically sealed, Gallium arsenide transistors to provide a
High
output power of 47.0 1dB Compression Point over the frequency range of
2170
MHz to 2200 MHz. Gain can be specified within the range of 40 to 53 dB,
gain
variation is +/-.5 dB. VSWR is 1.5:1 min. typical current is 20 Amps
dependent
on the gain and output power specification. All units include an
internal
voltage regulator and operate with +/-12V DC while providing
over-voltage
and reverse-polarity protection. The operating temperature range is -40
C
to +60 C with extended ranges available. This model is supplied with a
choice
of SMA or N type connectors.
12.7 to 13.25 GHz 2WATT
AMPLIFIER
12.7 TO 13.25GHz 2WATT
AmplifierMicrowave Solutions® introduces its new High Power amplifier
(HPA) MSH-7107701 with a 2 Watt Saturated Output Power and an IP3 of
-43 dBm over the frequency range of 12.7 to 13.25 GHz. It is designed
to be unconditionally stable for use in terrestrial communications
applications. This unit can be specified with a Gain ranging from 8 to
25dB, gain variation is +/-.5 dB. Noise Figure is better than 4.0dB and
input
I/O VSWR of 1.5:1 min. typical current is 1.5Amps dependent on the gain
and output power specification. All units include an internal voltage
regulator
and operate with a single input voltage of +12V DC while providing
overvoltage
and reverse-polarity protection. The operating temperature range is -40
C
to +60 C with extended ranges available. This model is supplied with
WR75.
Other connectorized configurations available.
|
